Brooches & Pins Made to Order: Carton Cube, Duty and the Freight Line That Surprises - HOLYCOME
Brooches & Pins · November 9, 2026 · 9 views

Brooches & Pins Made to Order: Carton Cube, Duty and the Freight Line That Surprises - HOLYCOME

Carton Cube, Duty and the Freight Line That Surprises Buyers

Last January, a US buyer of brooches and Pins placed 50 brooches and Pins against a sample signed in May. The first container landed with 9 pieces that failed on catch strength alone, and USD 15-50 landed on the buyer's P&L before a single unit sold, which is USD 15-118 on the Made to Order schedule.

On a 50-piece order at USD 15-118, a catch strength rate above two percent is not a quality surprise. It is a costing error that shows up as a credit note three weeks later.

Brooches & Pins wholesale piece from the HOLYCOME line in Wuzhou

Nothing in the rebuild was expensive. A gauge, a written limit and a retained tray did the work that a discount would only have delayed, and at USD 15-118 for 50 pieces that is the number the buyer signs.

The Made-to-Order Path for brooches and Pins

Made-to-order is a different production line, not a slower version of stock. It starts with a signed drawing, then a wax or resin model, then a casting, then setting, then finish, and each stage can fail on its own, priced at USD 15-118 for the 50-piece Made to Order run.

Twenty days is realistic for a new brooches and Pin when the model exists and only the stone changes. A new model adds a day for the CAD, a day for the print, and a day for the buyer to approve the render before metal is committed, on a 50-piece Made to Order order at USD 15-118.

The risk sits in approval, not in the bench. A buyer who approves a render on a phone screen and rejects the casting has bought a prototype, not a product. We send the render at 1:1 scale with a millimetre grid for that reason, and 50 pieces leaves Wuzhou in single-piece foam box at USD 15-118.

Brooches & Pins setting and finish detail on a HOLYCOME factory sample

The Three Failures We See Most in Incoming Samples

pin solder creep

A pin joined with soft solder creeps under load and tilts. Hard solder plus a mechanical seat holds it, on a 50-piece Made to Order order at USD 15-118.

Our countermeasure is a gauge and a written limit. It adds about 15 seconds per piece and removes the defect from the run rather than from the carton, the figure being USD 15-118 for a 50-piece run.

enamel pinholes

Enamel fired with trapped air shows pinholes after polish. Two thin coats beat one thick coat, and the Made to Order quote for it sits at USD 15-118.

In a 50-piece run this typically shows on 17 of pieces. Catching it means measuring catch pull strength at the tray level, not inspecting the finished carton, priced at USD 15-118 for the 50-piece Made to Order run.

catch strength

A safety catch that opens under fabric tension loses the piece. Catch tension needs a pull check, not a visual one, certified IGI report and packed single-piece foam box at 50 pieces.

The commercial effect is piece loss and replacement, typically USD 6-11 per brooch. Buyers who have seen it once put it in the purchase order; buyers who have not usually discover it on the first return, the figure being USD 15-118 for a 50-piece run.

What US buyers Check Before They Sign

At USD 15-118 per piece the four measurements below are worth more than the discount being negotiated. One of them costs nothing to write down.

Spec pointCommon trade outputHOLYCOME standardCost if missed
Clasp spring lifeSampled by handCycled 500 times on a jig per lotDetach claim and brand damage
Prong tension and seat depthChecked by feel at the benchPull-tested per piece, seat depth written on the sheetStone loss and total replacement
Hallmark depth and placementStamped where it fitsFixed position, depth measured so it never breaks the shankCustoms query and remaking
Solder flow at the jointNot inspectedJoint inspected under 10x before settingCrack at the seam in transit

Write these into the Made to Order purchase order and the arrival check becomes arithmetic instead of recollection, and the Made to Order quote for it sits at USD 15-118.

Order Terms, Sample Timing and Packing

The commercial frame is short enough to state in full. Minimum order is 50 pieces per design, and mixed designs travel in one shipment, so a 50-piece Made to Order order can carry three or four models without a separate setup charge. Sample pieces leave in 3-5 days when the components are in stock, and a new model adds about twenty days before the first article exists, which is how the Made to Order account reads it at USD 15-118.

Payment is 30 percent with the order and 70 percent against the bill of lading, with the balance window stated on the invoice rather than agreed by message. Prices quoted at USD 15-118 are FOB Guangzhou or Shenzhen; DDP is quoted separately because the duty line moves with the tariff schedule and not with our cost.

Packing follows the single-piece foam box format at 50 pieces to the carton, and the packing list carries SKU, size and stone size so receiving can count without opening every box. Private-label cartons add three days for the print run and must be approved before the first bulk order, not after it, with IGI report and single-piece foam box stated on the same sheet.

Certification is IGI report for the lots that carry it, with a batch report and per-piece measurement of catch pull strength for the lots below the threshold. The document set travels with the shipping papers, which is what a customs broker asks for at the port rather than after clearance, which is USD 15-118 on the Made to Order schedule.

A rejected tray is settled inside the same order cycle against the retained reference piece. If the difference sits on our retained sample we replace or credit; if it appeared in transit we split the assay cost and file with the carrier, and that rule is written on the order before the deposit clears, certified IGI report and packed single-piece foam box at 50 pieces.

Where USD 15-118 Per Piece Actually Goes

Cost at USD 15-118 leaves no room for assumption. The table shows which line compresses and which line only moves quality down.

Cost lineShareWhat moves it
Base metal or alloy for brooches and Pins30%Alloy choice and casting yield
Stone or melee for brooches and Pins20%Sieve range and lot batching
Setting and finishing labor for brooches and Pins19%Jig design and bench minutes
Plating, polish and QC for brooches and Pins12%Per-tray versus per-piece checks
Packaging for brooches and Pins19%single-piece foam box

A factory that cannot state its bench minutes per piece has never costed its own line. Ask for minutes and for the reject rule, not for a discount, priced at USD 15-118 for the 50-piece Made to Order run.

What a Report Proves and What It Does Not

The figure below is what we quote for brooches and Pins, and it is deliberately narrower than the market average, on a 50-piece Made to Order order at USD 15-118.

Three numbers decide it for brooches and Pins: the tolerance band, the inspection density and the responsibility clause. Write all three down and the rest of the negotiation is arithmetic. Leave any of them out and it becomes a discussion about intent, on a 50-piece Made to Order order at USD 15-118.

We send a one-page sheet with every brooches and Pins quote that states those three, plus the retained-tray rule. Buyers who compare on it usually find that the gap between suppliers is smaller than the gap between the specs they were comparing, certified IGI report and packed single-piece foam box at 50 pieces.

The Sample Approval That Survives Production

Most brooches and Pins disputes we arbitrate trace back to this line, not to the defect itself, certified IGI report and packed single-piece foam box at 50 pieces.

There is a version of this that looks cheaper on paper and costs more in practice: quoting the best case on brooches and Pins and letting the buyer discover the spread. It works once. The second order goes to whichever supplier quoted honestly, which the Made to Order file records at USD 15-118 in single-piece foam box.

We would rather lose a first order of brooches and Pins on price than explain a defect after it lands. That position is unusual in this category and it is the reason our reorder share is high, and at USD 15-118 for 50 pieces that is the number the buyer signs.

What This Means for a First Order

A first Made to Order order of 50 pieces per design at USD 15-118 tests the line rather than the range. Three designs covers the shelf.

Ask for the retained tray and the IGI report batch sheet with the first shipment. Both are free and both decide the reorder, on a 50-piece Made to Order order at USD 15-118.

Freight, Duty and the Arrival Check

Export runs through Guangzhou or Shenzhen. Air lands in 5-8 days on the US west coast, 7-10 on the east, and sea takes roughly three times the transit, which is how the Made to Order account reads it at USD 15-118.

FOB is the default on brooches and Pins and DDP is the option. Buyers new to the US market usually take DDP once, then switch after they see the breakdown, which the Made to Order file records at USD 15-118 in single-piece foam box.

If catch strength appears in the arrival check, the retained tray decides who owns it. Keep the IGI report batch sheet in the same folder as the packing list, which the Made to Order file records at USD 15-118 in single-piece foam box.

How a Repeat Order Gets Built

Nothing in this sequence is unusual, and that is the point. Each step exists because skipping it produced a specific failure on a previous order, and the Made to Order quote for it sits at USD 15-118.

  1. Sign the drawing at 1:1 scale with a millimetre grid, not a phone render.
  2. Cut the model in wax or resin and photograph it on the gauge before metal is committed.
  3. Cast the first article, set the stones and finish it exactly as bulk will be finished.
  4. Send the first article for approval with the weight and the stone measurements stated.
  5. Run the balance of the order in 25-30 days, holding the approved article as the reference.
  6. Ship with the approved article photographed beside a production piece from the same tray.

Reorders inside this sequence run 12-15 days because the model, the gauge set and the signed spec stay in our system, and 50 pieces leaves Wuzhou in single-piece foam box at USD 15-118.

Frequently Asked Questions

Can you ship DDP?

DDP is available for US accounts and removes the duty invoice that arrives after the carton clears. FOB Guangzhou or Shenzhen is the default, and most buyers take DDP once and then switch after they see the breakdown, and at USD 15-118 for 50 pieces that is the number the buyer signs.

How long does a reorder of the same brooches and Pin take?

With the model, the gauge set and the signed spec already in our system, a repeat is 12-15 days; a first run is 3-5 days for a stock-component sample and about 20 days when a new model is needed, quoted at USD 15-118 per piece in single-piece foam box.

What finish do you use, and how thick is it?

Rhodium at 0.20 micron minimum on white brooches and Pins, with a palladium strike layer so wear-through reads white rather than yellow. Vermeil runs at 3 microns over sterling and is logged per lot, which is USD 15-118 on the Made to Order schedule.

How is brooches and Pins packed for single-piece foam box?

Every unit goes into a foam-backed pouch, then the single-piece foam box, then the outer carton at 50 pieces. The packing list carries the SKU, the size and the stone size so receiving can check without opening every box, priced at USD 15-118 for the 50-piece Made to Order run.

Can you ship DDP?

DDP is available for US accounts and removes the duty invoice that arrives after the carton clears. FOB Guangzhou or Shenzhen is the default, and most buyers take DDP once and then switch after they see the breakdown, and at USD 15-118 for 50 pieces that is the number the buyer signs.

Next Step

The next step is a sample in 3-5 days, not a container. Write to service@holycome.com or WhatsApp +86 18078079070, subject Made to Order, shipped as single-piece foam box and certified IGI report.

HOLYCOME is operated by Wuzhou HengliLai Jewelry Co., Ltd., a factory in Wuzhou, Guangxi, producing since 2009 at roughly 60,000 pieces a month. Contact service@holycome.com or WhatsApp +86 18078079070, which is USD 15-118 on the Made to Order schedule.

Related reading: Brooches & Pins Private Label Carton: Alloy, Karat and the Cost of a Color Change - HOLYCOME Hair Accessories Q4 Holiday Stock: Sample to Container: The Real Calendar - HOLYCOME

Request Wholesale Quote

Written by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.

Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.

Reviewed for accuracy by our quality team before publication. Last updated .

Related Articles