Bulk Mix Lots Wholesale: The Sample Approval That Survives Production - HOLYCOME
Bulk Mix Lots · November 9, 2026 · 10 views

Bulk Mix Lots Wholesale: The Sample Approval That Survives Production - HOLYCOME

The Sample Approval That Survives Production

Two buyers ordered the same bulk Mix Lot in the same month. One paid 9% less and absorbed 23 rejects out of 420 pieces; the other paid our quote and shipped clean. The difference was nickel release, and it was measurable on both benches.

The defect did not surprise us. nickel release is the predictable output of a run where nobody wrote the tolerance down, and it is the first measurement we take on an incoming bulk Mix Lot. It is written into the bulk Mix Lots spec sheet that travels with the quote, so the bench and the buyer read the same number.

Bulk Mix Lots wholesale product photo from the HOLYCOME line in Wuzhou

We did not discount the quote. We changed the gauge, the seat cut, the plating log and the tray rule, and the second run shipped with zero rejects on plating thickness per batch and nickel release compliance. It is written into the bulk Mix Lots spec sheet that travels with the quote, so the bench and the buyer read the same number.

What North American buyers Check Before They Sign

Price is the first thing compared and the last thing that matters. These four measurements decide the return rate on bulk Mix Lots, and three of them cost nothing to specify. It is written into the bulk Mix Lots spec sheet that travels with the quote, so the bench and the buyer read the same number.

Spec pointCommon trade outputHOLYCOME standardCost if missed
Nickel Release on bulk Mix LotsInspected visually at the trayGauntlet check on every piece, limit written in the specReturns inside 60 days of wear
Plating Thickness Drift on bulk Mix LotsBatch dependent, not loggedThickness and tension logged per lotComplaint after the second season
Stone Setting Speed on bulk Mix LotsEstimated from nominalGauged per size with go/no-go toolsResize queue and reship cost
Tolerance stack-up on bulk Mix LotsQuote states nominal onlyWorst-case band published per SKUFreight and duty drift

None of these are premium features. They cost seconds per piece and they remove the reason a buyer has to inspect twice. It is written into the bulk Mix Lots spec sheet that travels with the quote, so the bench and the buyer read the same number.

Where USD 2-18 Per Piece Actually Goes

The cost of a bulk Mix Lot in the USD 2-18 band splits roughly as below. The line buyers challenge most is labor, and it is the line that decides whether the piece survives a season. It is written into the bulk Mix Lots spec sheet that travels with the quote, so the bench and the buyer read the same number.

Bulk Mix Lots close-up of setting and finish, HOLYCOME factory sample
Cost lineShareWhat moves it
Base metal or alloy for bulk Mix Lots34%Alloy choice and casting yield
Stone or melee for bulk Mix Lots25%Sieve range and lot batching
Setting and finishing labor for bulk Mix Lots22%Jig design and bench minutes
Plating, polish and QC for bulk Mix Lots15%Per-tray versus per-piece checks
Packaging and freight for bulk Mix Lots4%Box grade and DDP versus FOB

If a supplier will not break out the five lines above, the number you are comparing is not a price. It is a total that somebody else assembled from assumptions. It is written into the bulk Mix Lots spec sheet that travels with the quote, so the bench and the buyer read the same number.

The Three Failures We See Most in Incoming Samples

nickel release

EU and some US buyers require nickel-release compliance. A plating bath that passes on day one can fail after a barrel top-up.

Our countermeasure is a gauge and a written limit. It adds about 8 seconds per piece and removes the defect from the run rather than from the carton.

plating thickness drift

A 3 micron layer survives a season; a 1.5 micron layer does not. Thickness is measurable and should be stated per batch.

In a 420-piece run this typically shows on 14 of pieces. Catching it means measuring plating thickness per batch at the tray level, not inspecting the finished carton.

stone setting speed

Glue-set stones that pool adhesive above the seat photograph as a white dot. Recessed seats fix it at the bench.

The commercial effect is chargebacks and listing takedowns, typically USD 2-5 per piece. Buyers who have seen it once put it in the purchase order; buyers who have not usually discover it on the first return.

The Sample Approval That Survives Production

Most bulk Mix Lots disputes we arbitrate trace back to this line, not to the defect itself.

What buyers underestimate on alloy pieces is the cost of the interruption, not the cost of the piece. A missing 6% of a run stalls a launch, and a stalled launch costs more than the 6% ever did.

We plan a 3-5% buffer on first runs of bulk Mix Lots and tell the buyer it exists. Hiding a buffer and shipping it as production is how a supplier trains a buyer to distrust the count.

How a Repeat Order Gets Built

Our process is deliberately boring, because boring is what survives a bulk run with several sets of hands on it. It is written into the bulk Mix Lots spec sheet that travels with the quote, so the bench and the buyer read the same number.

  1. Spec sheet signed before casting: cast or stamped, tolerances, plating thickness and packing format.
  2. Sample in 3-5 working days from stock components, or about 20 days if a new model is required.
  3. Production photos at three checkpoints: raw cast, post-polish, post-set, with buyer approval at each.
  4. Bulk in 15-20 days under 500 pieces; custom tooling runs 25-30 days.
  5. Pre-shipment QC report with per-tray counts and a retained reference tray for disputes.

A first order at 50 pieces per design is a measurement rather than a purchase. It tells you what plating thickness per batch and nickel release compliance looks like from this line. It is written into the bulk Mix Lots spec sheet that travels with the quote, so the bench and the buyer read the same number.

Carton Cube, Duty and the Freight Line That Surprises Buyers

This is the question that separates a trading company from a factory, and on bulk Mix Lots the answer is usually shorter than buyers expect.

In US wholesale terms, this is the difference between a landed cost the buyer can plan against and a number that moves after the container ships. For alloy pieces, we publish the figure per SKU and hold it for the order window rather than for the calendar year.

Practically, it shows up in three places for alloy pieces: the proforma, the QC sheet and the credit note if something goes wrong. All three should quote the same number. When they do not, the argument is about paperwork, not about the product.

What a Report Proves and What It Does Not

In US wholesale, this is the single most negotiated line on bulk Mix Lots and the least documented one.

Three numbers decide it for alloy pieces: the tolerance band, the inspection density and the responsibility clause. Write all three down and the rest of the negotiation is arithmetic. Leave any of them out and it becomes a discussion about intent.

We send a one-page sheet with every bulk Mix Lots quote that states those three, plus the retained-tray rule. Buyers who compare on it usually find that the gap between suppliers is smaller than the gap between the specs they were comparing.

Sample to Container: The Real Calendar

Buyers who have run three programs on bulk Mix Lots know this instinctively; first-time buyers learn it the expensive way.

There is a version of this that looks cheaper on paper and costs more in practice: quoting the best case on alloy pieces and letting the buyer discover the spread. It works once. The second order goes to whichever supplier quoted honestly.

We would rather lose a first order of alloy pieces on price than explain a defect after it lands. That position is unusual in this category and it is the reason our reorder share is high.

What This Means for a First Order

A test run at 50 pieces tells you three things: whether nickel release is controlled, whether packing survives freight, and whether the count is honest. It is written into the bulk Mix Lots spec sheet that travels with the quote, so the bench and the buyer read the same number.

Buyers who run that measurement before committing a season usually keep the supplier. Buyers who skip it usually pay twice for the same lesson. It is written into the bulk Mix Lots spec sheet that travels with the quote, so the bench and the buyer read the same number.

Freight, Duty and the Arrival Check

We ship from Guangzhou or Shenzhen, and the port choice follows the carrier rate rather than a fixed habit. It is written into the bulk Mix Lots spec sheet that travels with the quote, so the bench and the buyer read the same number.

DDP is available for US accounts that want duty and clearance on our side, and it removes the invoice that arrives after the carton clears. It is written into the bulk Mix Lots spec sheet that travels with the quote, so the bench and the buyer read the same number.

On arrival, weigh a tray and measure ten pieces. Anything outside the band is a claim with evidence rather than a difference of opinion. It is written into the bulk Mix Lots spec sheet that travels with the quote, so the bench and the buyer read the same number.

Frequently Asked Questions

What is the minimum order for bulk Mix Lots?

50 pieces per bulk Mix Lot. Designs mix inside one shipment, so a first order of three designs at 50 pieces each is normal for a new US account. Below 50 we cannot keep the gauge check independent of the shift, which is the part buyers actually pay for on bulk Mix Lots.

How long does a reorder of the same bulk Mix Lot take?

12-15 days for bulk Mix Lots, because the model, the gauge set and the signed spec stay in our system. A first run is longer: 3-5 days for a stock-component sample, about 20 days if a new model is needed, then 15-20 days for bulk under 500 pieces.

Do you supply certificates for bulk Mix Lots?

nickel release test per batch for bulk Mix Lots. Below that threshold we supply a batch report plus per-piece measurement of plating thickness per batch, which is what most resellers need at the counter.

What finish do you use on bulk Mix Lots, and how thick is it?

Rhodium at 0.20 micron minimum on white bulk Mix Lots, with a palladium strike layer so wear-through reads white rather than yellow. Thickness is logged per lot and appears on the QC sheet, not only in the brochure.

How do you handle a rejected tray of bulk Mix Lots?

We replace or credit inside the same order cycle. The retained reference tray decides: if nickel release shows on our retained bulk Mix Lot we own it, and if it appeared in transit we split the assay cost and file with the carrier. A typical exposure on bulk Mix Lots is chargebacks and listing takedowns, typically USD 2-5 per piece.

Next Step

If you are quoting bulk Mix Lots against another supplier, send that quote. We will mark the four lines where the numbers diverge and let you decide. It is written into the bulk Mix Lots spec sheet that travels with the quote, so the bench and the buyer read the same number.

The factory behind bulk Mix Lots here is Wuzhou HengliLai Jewelry Co., Ltd., operating since 2009 in Wuzhou, Guangxi, at roughly 60,000 pieces a month. Reach the export desk at service@holycome.com or +86 18078079070 on WhatsApp.

Related reading: Alloy Rings Bulk: What the Quote Actually Covers - HOLYCOME Bracelets & Bangles Bulk: AQL, Tray Checks and What a QC Report Should Say - HOLYCOME

Request Wholesale Quote

Written by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.

Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.

Reviewed for accuracy by our quality team before publication. Last updated .

Related Articles